engine heads and blocks
Haltech HT-220001 Nexus Rebel LS - ECU Only
$1,595
Made to order
Universal fit — no vehicle-specific fitment required.
Qty
1
Free freight ≥ $999 · $40 flat below
About this part
Nexus Rebel LS - ECU Only
Specifications
| PROP65 | Yes |
|---|---|
| PCDB CATEGORY | Engine |
| COUNTRY OF ORIGIN | AU |
| PART TERMINOLOGY | Engine Control Module (ECM) |
| 12 X ONBOARD TEMP. SENSING ZONES | ECU: -40 to 125°C (-40 to 255°F)_x000D_
 |
| PDM | -40 to 150°C (-40 to 302°F) |
| 4 CHANNEL OSCILLOSCOPE | 50kSa/s per channel 2ms/Div limit |
| ANALOG VOLTAGE INPUTS (USER DEFINABLE) | 2 |
| ANTI LAG/ROTATIONAL IDLE | YES |
| AUXILIARY AX25+ OUTPUT (25 A) (USER DEFINABLE) | 1 |
| BOOST CONTROL | 3D Closed Loop |
| CAN / TRANSMISSION POWER SUPPLY (8 A) | 2 |
| CAN BUS NETWORK (HALTECH CAN DEVICES ONLY) | 1 |
| CAN NETWORK | 1 |
| CLOSED LOOP O2 CONTROL | YES |
| CO2 CONTROL | YES |
| COOLANT / AIR TEMPERATURE INPUT | 2 |
| DATA LOGGING | Laptop + Onboard |
| DIFFERENTIAL ENGINE POSITION INPUTS | 2 (Trigger and Home) |
| DIGITAL PULSED OUTPUTS (USER DEFINABLE) | 5 |
| DISPLAY NAME | Nexus Rebel LS - ECU Only |
| DRIVE BY WIRE THROTTLE SUPPORT | Single |
| ENCLOSURE (NOT INCLUDING CONNECTOR PROTRUSION) | 196 x 130 x 44.5 mm (7.7 x 5.2 x 1.8 in) |
| ENGINE PROTECTION | Multi Level |
| FAN CONTROL (25 A) | 1 |
| FLAT SHIFT CONTROL | Advanced |
| FLEX FUEL | YES |
| FUEL / OIL PRESSURE INPUT | 2 |
| FUEL PUMP CONTROL (25 A) | 1 |
| HALF BRIDGE OUTPUTS (IAC OR DRIVE BY WIRE THROTTLE) | 4 |
| HIGH SPEED USB 2.0 (USB C INTERFACE) 480 MBIT/S CONNECTION | 1 |
| IGNITION | 8 |
| IGNITION / INJECTOR POWER SUPPLY (25 A) | 1 |
| INJECTOR (HIGH IMPEDANCE ONLY) | 8 |
| KNOCK CONTROL | YES |
| KNOCK SENSOR INPUTS | 2 |
| LAUNCH CONTROL | YES |
| LOGGING LOCATION | Onboard or PC logging |
| LONG TERM LEARNING | Up to 3D |
| LOW POWER MODE (USB) | 4 to 5.5V |
| MAP SENSOR INPUT | 1 |
| MAX CHANNELS PER LOG | 300 |
| MAX SAMPLING FREQUENCY | 1kHz |
| NITROUS CONTROL STAGE | 6 |
| NO OUTPUT STATIC CURRENT DRAW | < |
| ON BOARD WIDEBAND | Single Channel LSU 4.9 |
| ON BOARD WIDEBAND CONTROLLER (BOSCH LSU 4.9 SENSOR ONLY) | 1 |
| ONBOARD MAP SENSOR (4 BAR) | 1 |
| ONBOARD STORAGE | 32MB |
| OPERATING TEMPERATURE (AMBIENT) | -40 to 85°C (-40 to 185°F) |
| OVERALL (INCLUDING CONNECTOR PROTRUSION) | 196 x 149 x 44.5 mm (7.7 x 5.9 x 1.8 in) |
| POWER SUPPLY (ACROSS POWER TERMINALS) | 8 to 22V |
| POWER UP OVER USB | Datalogging settings and firmware upgrade available |
| PRODUCT TYPE | ECU |
| PROP 65 (C R OR CR) | CR |
| PROP 65 SHORT LABEL | Prop 65 Warning Label.JPG |
| PROP 65 YES/NO | Yes |
| RACE TIMER | YES |
| RIDE HEIGHT | YES |
| STATIC CURRENT DRAW FROM USB PORT | < |
| SYNCHRONISED PULSED INPUTS (USER DEFINABLE) | 4 |
| TACHOMETER OUTPUT | 1 |
| THROTTLE POSITION / PEDAL POSITION INPUT | 4 |
| TRACTION CONTROL | YES |
| TRANS BRAKE | YES |
| TRANSMISSION / VEHICLE SPEED SENSOR INPUTS | 2 |
| TUNING TABLE RESOLUTION | 32 x 32 |
| WEIGHT | 1.15 kg (2.53 lbs) |
| WI FI | 900 kB/s datalog extraction. Hardware lockout for security |
Datasheet — not yet published